All services

HVAC Furnace Installation and Replacement in Pittsburgh, PA

Overview

New furnace installation and full system replacement for Pittsburgh homes, including removal of the old unit and cleanup when the work is done. Free estimates included.

Whether your furnace has reached the end of its useful life or you're replacing a system that's failed mid-winter, Impact HVAC sizes and installs the right unit for your home's square footage, duct configuration, and fuel source. Tight mechanical rooms and difficult access are part of the job, not a reason for surprise charges. The old equipment is hauled away, the space is left clean, and the system is walked through with you before the crew leaves.

What's included

  • Free Installation Estimate
  • Old Unit Removal
  • Duct Compatibility Check
  • Permit and Inspection Handled

When a Pittsburgh winter hits and your furnace stops keeping up, you don't have time to wonder whether a repair is worth it or whether a new system will even fit your basement. Impact HVAC handles furnace installation and replacement for homes throughout Pittsburgh, Mt. Lebanon, and Dormont, including the older row houses and hillside properties where a straightforward swap is rarely straightforward. Whether your current unit is 20 years old and limping through January or it finally gave out overnight, the goal is a properly sized, correctly installed system that heats your home reliably without leaving you guessing about what you paid for.

Pittsburgh's Zone 5A climate means furnaces here aren't running occasionally — they're running hard from November through March, cycling through freeze-thaw swings that wear on igniters, heat exchangers, and ductwork connections faster than homeowners expect. A furnace that was borderline last spring may not make it through February.

What a Furnace Replacement Actually Covers

A furnace installation isn't just dropping in a new unit. It starts with sizing your home correctly, because an oversized furnace short-cycles and an undersized one never quite catches up on the coldest nights. Impact HVAC installs both gas and electric furnaces and handles the full scope: disconnecting and removing the old equipment, making any needed duct or flue connections, and verifying that the new system is running at the right airflow and temperature before leaving. Old equipment gets hauled away. If your home needs any electrical or gas line adjustments to support the new unit, that gets addressed as part of the process, not discovered after the fact.

Signs Your Furnace Has Reached the End

Most furnaces have a lifespan of 15 to 20 years, and the signs they're done tend to cluster: rising gas bills without a change in usage, uneven heat from room to room, a heat exchanger that's cracked or corroded, or a system that's been repaired multiple times in the past few seasons. If your repair costs are approaching half the price of a replacement, or if a technician has flagged a heat exchanger issue, replacement is usually the more honest recommendation. A system that keeps breaking down in January is a liability, not an asset.

What Older Pittsburgh Homes Demand from a Furnace Install

Homes built before 1960 make up a significant share of Pittsburgh's housing stock, and many of them were never designed with modern HVAC in mind. Cramped mechanical rooms, low basement ceilings, original ductwork that runs in unexpected directions, and tight access points on hillside lots all add complexity that a one-size-fits-all approach can't handle. In neighborhoods like Dormont, where brick construction and narrow lots are the norm, getting equipment in and out without damaging finished spaces takes planning. Mt. Lebanon homes from the postwar era often have ductwork layouts that need adjustment when moving from an older, lower-efficiency unit to a modern 96% AFUE furnace with different venting requirements. Impact HVAC pulls the necessary permits and coordinates inspections, so you're not left holding liability questions after the job is done.

What to Expect When You Schedule

The process starts with a free estimate that covers what your home actually needs, not a ballpark that grows once work begins. You'll get a clear breakdown of equipment, labor, and any related work before anything is approved. On installation day, the crew handles removal, installation, and cleanup. Before leaving, they verify the system is heating correctly, walk you through the thermostat settings, and answer questions about filters, maintenance schedules, and what to watch for in the first few weeks. Licensed, insured, and familiar with Pittsburgh's permitting requirements, Impact HVAC treats a completed install as one that's confirmed working, not one that's just mechanically connected.

Pricing

Contact us for a free estimate

Pricing is confirmed during your initial consultation and may vary based on your specific situation and scope of work.

Get a Free Estimate (412) 297-1852

Common questions

How do you determine what size furnace my home needs?
Sizing is done through a load calculation that accounts for your home's square footage, insulation, window placement, ceiling height, and ductwork layout — not just a guess based on what was there before. Older Pittsburgh homes especially can't be sized by rule of thumb, because a century-old row house with plaster walls and a partially finished basement heats very differently from a newer build of the same square footage. Installing the right size matters for both comfort and efficiency.
Can you work with my existing ductwork, or will I need to replace that too?
In many cases, existing ductwork can stay in place, though it gets inspected for leaks, sizing issues, or connections that won't work properly with the new system. If adjustments are needed, those are identified during the estimate, not discovered mid-installation. Homes with older flex duct or original metal runs sometimes need targeted repairs rather than a full replacement, and that gets communicated clearly before any work begins.
What happens to my old furnace after it's removed?
The old equipment is disconnected and hauled away as part of the installation. You don't need to arrange separate disposal or worry about it sitting in your basement or driveway.
Do you handle gas line and venting work if my new furnace has different requirements?
Yes. High-efficiency furnaces often require PVC venting instead of traditional flue connections, and the gas line may need adjustment depending on the new unit's BTU rating. These aren't add-ons that surface after the fact — they're factored into the estimate upfront so the final cost reflects the full scope of what your home needs.
How long does a furnace installation typically take?
Most residential installations are completed in a single day, typically four to eight hours depending on the complexity of the access and any ductwork or venting modifications required. Homes with tight basements or non-standard layouts may take longer, and that's something Impact HVAC can give you a realistic timeframe on during the estimate visit.

Get a straight answer before you decide

Call for a free estimate and find out exactly what your system needs — no pressure, no guesswork.